eLibrary >
PD CEN/TS 16459:2013 External fire exposure of roofs and roof coverings. Extended application of test results from CEN/TS 1187 >
PD CEN/TS 16459:2013 External fire exposure of roofs and roof coverings. Extended application of test results from CEN/TS 1187, 2013
- Foreword
- Introduction
- Figure 1 – Decision process on classification of roofs/roof coverings
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 Product and end-use application parameters for roof coverings/roof systems
- Table 1 — List of product parameters and end-use applications parameters
- 5 Extended application [Go to Page]
- 6 Influence of product parameters and end-use application parameters on external exposure to fire test performance
- Table 2 — Exposure conditions for CEN/TS 1187 tests 1 to 4
- Table 3 — The standard tested angle of pitch for CEN/TS 1187 tests 1 to 4
- Table 4 — Potential impact of parameters and particular characteristics when tested to CEN/TS 1187
- 7 General guidance to the annexes for Application Rules
- Table 5 — Contents of annexes, arranged according to product groups (A.3.1/D.3.1 to A.3.12/D.3.12), and information on the contribution of components (A.4.1 to A.4.5) to the fire performance
- Annex A (normative) Application rules for test results from CEN/TS 1187 test 1, per product group and/or components
- A.1 General
- Figure A.1 – Example Sketch
- A.2 General rules, valid for every product within a product group and/or component
- A.3 Product groups
- A.3.1 Slates and tiles
- A.3.1.1 slates and tiles, non-metallic
- A.3.1.2 Metallic tiles
- A.3.2 Small elements
- A.3.2.1 General
- A.3.2.2 Bitumen shingles
- A.3.2.3 Miscellaneous small elements
- A.3.3 Reinforced bitumen sheets
- A.3.4 Plastic and rubber sheets
- A.3.5 Roof-lights
- A.3.6 Glazing systems
- A.3.7 Profiled non-metallic sheets
- A.3.7.1 Profiled fibre cement sheets
- A.3.7.2 Profiled bitumen based sheets
- A.3.7.3 Miscellaneous profiled non-metallic sheets
- A.3.8 Composite metallic sandwich panels
- A.3.9 Profiled metal sheets
- A.3.10 Flat metal sheets
- A.3.11 Liquid applied roof waterproofing kits
- A.3.12 Miscellaneous
- A.4 Components
- A.4.1 Adhesive
- A.4.2 Separating layer
- A.4.3 Insulation layer
- A.4.4 Vapour Barrier
- A.4.5 Supporting deck
- Annex B (normative) Application rules for test results from CEN/TS 1187 Test 2, per product group
- B.1 General
- B.2 General rules, valid for every product within a product group
- B.3 Product groups
- B.3.1 Slates and tiles
- B.3.1.1 Non-metallic slates and tiles (reaction-to-fire-class A1 to A2-s3 d2 according to EN 13501-1)
- B.3.1.2 Metallic tiles
- B.3.2 Small elements (reaction-to-fire-class B-s1,d0 to F according to EN 13501-1)
- B.3.2.1 General
- B.3.2.2 Bitumen shingles
- B.3.2.3 Miscellaneous small elements
- B.3.3 Reinforced bitumen sheets
- B.3.4 Plastic and rubber sheets
- B.3.5 Roof-lights
- B.3.6 Glazing systems
- B.3.7 Profiled non-metallic sheets
- B.3.7.1 Profiled fibre cement sheets
- B.3.7.2 Profiled bitumen based sheets
- B.3.7.3 Miscellaneous profiled non-metallic sheets
- B.3.8 Composite metallic sandwich panels
- B.3.9 Profiled metal sheets
- B.3.10 Flat metal sheets
- B.3.11 Liquid applied waterproofing kits
- B.3.12 Miscellaneous
- Annex C (normative) Application rules for test results from CEN/TS 1187 test 3, per product group
- C.1 General
- Figure C.1 – Example sketch
- C.2 General rules, valid for every product within a product group
- C.3 Product groups
- C.3.1 Slates and tiles
- C.3.1.1 Non-metallic slates and tiles (reaction-to-fire-class A1 to A2 – s3 d2, according to EN 13501-1)
- C.3.1.2 Metallic Tiles
- C.3.2 Small elements (reaction-to-fire-class B – s1, d0 to F; according to EN 13501-1)
- C.3.2.1 General
- C.3.2.2 Bitumen Shingles
- C.3.2.3 Miscellaneous small elements
- C.3.3 Reinforced bitumen sheets
- C.3.3.1 General
- C.3.3.2 Typical roof waterproofing system
- Figure C.2 – Dimensions of the supporting deck of the test specimen for reinforced bitumen sheets
- Figure C.3 – Outline of insulation boards with one longitudinal joint and staggered joints parallel to the short side of the specimen
- Figure C.4 – Position of joints. Left hand side: joint in the first (lower) layer of a double-layer roof waterproofing system. Right hand side: joints both in the upper layer of a double layer roof waterproofing system and in a single-layer waterproof...
- Figure C.5 – Example sketch
- C.3.4 Plastic and rubber sheets
- C.3.4.1 General
- C.3.4.2 Typical roof waterproofing system
- Figure C.6 – Dimensions of the supporting deck of the test specimen for plastic and rubber sheets
- Figure C.7 – Outline of insulation boards with one longitudinal joint and staggered joints parallel to the short side of the specimen
- Figure C.8 – Position of joints. Left hand side: joint in the first (lower) layer of a double-layer roof waterproofing system. Right hand side: joints both in the upper layer of a double layer roof waterproofing system and in a single-layer waterproof...
- C.3.5 Roof-lights
- C.3.6 Glazing systems
- C.3.7 Profiled non-metallic sheets
- C.3.7.1 Profiled fibre cement sheets
- C.3.7.2 Profiled bitumen-based Sheets
- C.3.7.3 Miscellaneous profiled non-metallic sheets
- C.3.8 Composite metallic sandwich panels
- C.3.9 Profiles metal sheets
- C.3.10 Flat metal sheets
- C.3.11 Liquid applied roof watering kits
- C.3.12 Miscellaneous
- Annex D (normative) Application rules for test results from CEN/TS 1187 Test 4 for individual product groups
- D.1 General
- Figure D.1 – Example sketch
- D.2 General EXAP rules for CEN/TS 1187 test 4, valid for every product within a product group
- D.3 Product groups
- D.3.1 Slates and tiles
- D.3.1.1 Non-metallic slates and tiles
- D.3.1.2 Metallic slates and tiles
- D.3.2 Small elements
- D.3.2.1 General
- D.3.2.2 Bitumen shingles
- D.3.2.3 Miscellaneous small elements, e.g. plastic tiles
- D.3.3 Reinforced bitumen sheets (same as bitumen shingles)
- Table D.1 — Reinforced bitumen membranes and product parameters
- D.3.4 Plastic and rubber sheets
- D.3.5 Roof-lights
- D.3.6 Glazing systems
- D.3.7 Profiled non-metallic sheets
- D.3.7.1 Profiled fibre cement sheets
- D.3.7.2 Profiled bitumen based sheets
- D.3.7.3 Miscellaneous profiled non-metallic sheets
- D.3.8 Composite (including metal faced) sandwich panels
- D.3.9 Profiled metal sheets
- D.3.10 Flat metal sheets
- D.3.11 Liquid applied roof water-proofing kits
- D.3.12 Miscellaneous
- Bibliography [Go to Page]