eLibrary >
BS EN ISO 19432-1:2020 Building construction machinery and equipment. Portable, hand-held, internal combustion engine-driven abrasive cutting machines - Safety requirements for cut-off machines for centre-mounted rotating abrasive wheels >
BS EN ISO 19432-1:2020 Building construction machinery and equipment. Portable, hand-held, internal combustion engine-driven abrasive cutting machines - Safety requirements for cut-off machines for centre-mounted rotating abrasive wheels, 2020
- undefined
- Annex ZA (informative)Relationship between this European Standard and the essential requirements of Directive 2006/42/EC machinery, and amending Directive 95/16/EC (recast) [2006 L157] aimed to be covered
- Foreword
- Introduction
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 Safety requirements and verification
- 4.1 General
- 4.2 Handles
- 4.2.1 Requirements
- 4.2.2 Verification
- 4.3 Spindle speed
- 4.3.1 Requirement
- 4.3.2 Verification
- 4.4 Engine-starting device
- 4.4.1 Requirements
- 4.4.2 Verification
- 4.5 Engine-stopping device
- 4.5.1 Requirements
- 4.5.2 Verification
- 4.6 Throttle control system
- 4.6.1 Dimensions
- 4.6.2 Operation
- 4.6.3 Throttle lock
- 4.7 Clutch
- 4.7.1 Requirements
- 4.7.2 Verification
- 4.8 Exhaust gases
- 4.8.1 Requirements
- 4.8.2 Verification
- 4.9 Cutting-debris discharge
- 4.9.1 Requirements
- 4.9.2 Verification
- 4.10 Fuel tanks, oil tanks and fuel lines
- 4.10.1 Tank filler location and identification
- 4.10.2 Tank filler openings
- 4.10.3 Verification
- 4.11 Protection against contact with parts under high voltage
- 4.11.1 Requirements
- 4.11.2 Verification
- 4.12 Transmission cover(s)
- 4.12.1 Requirements
- 4.12.2 Verification
- 4.13 Protection against contact with hot parts
- 4.13.1 Requirements
- 4.13.2 Verification
- 4.14 Cut-off wheel guard
- 4.14.1 Requirements
- 4.14.2 Verification
- 4.15 Flange locking device
- 4.15.1 Requirements
- 4.15.2 Verification
- 4.16 Flange assembly
- 4.16.1 Requirements
- 4.16.2 Verification
- 4.17 Spindle diameter
- 4.17.1 Requirements
- 4.17.2 Verification
- 4.18 Special tools
- 4.18.1 Requirements
- 4.18.2 Verification
- 4.19 Noise
- 4.19.1 Reduction by design at source and by protective measures
- 4.19.2 Noise measurement
- 4.20 Vibration
- 4.20.1 Reduction by design at source and by protective measures
- 4.20.2 Vibration measurement
- 4.21 Electromagnetic immunity
- 4.21.1 Requirements
- 4.21.2 Verification
- 5 Information for use
- 5.1 Instruction handbook
- 5.1.1 General
- 5.1.2 Technical data
- 5.1.3 Other information
- 5.2 Markings
- 5.3 Warnings
- 5.4 Test of labels
- 5.4.1 General
- 5.4.2 Preparation of test specimens and control specimens
- 5.4.3 Wipe resistance test
- 5.4.4 Adhesion test
- Annex A (normative) Strength test of cut-off wheel guard
- Annex B (normative) Noise test code — Engineering method (grade 2 of accuracy)
- Annex C (normative) Measurement of vibration values at the handles
- Annex D (normative) Cut-off machine positions
- Annex E (normative) Summary of results from round-robin tests (2007 and 2008) on one cut‑off machine
- Annex F (informative) List of significant hazards
- Bibliography [Go to Page]