Already a subscriber? 
MADCAD.com Free Trial
Sign up for a 3 day free trial to explore the MADCAD.com interface, PLUS access the
2009 International Building Code to see how it all works.
If you like to setup a quick demo, let us know at support@madcad.com
or +1 800.798.9296 and we will be happy to schedule a webinar for you.
Security check
Please login to your personal account to use this feature.
Please login to your authorized staff account to use this feature.
Are you sure you want to empty the cart?
PD CEN/TS 12201-7:2014 Plastics piping systems for water supply, and for drainage and sewerage under pressure. Polyethylene (PE) - Guidance for the assessment of conformity, 2014
- 64_e_stf.pdf [Go to Page]
- Contents Page
- Foreword
- Introduction
- Figure 1 — Typical scheme for the assessment of conformity by a manufacturer
- Figure 2 — Typical scheme for the assessment of conformity by a manufacturer, including certification
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 Abbreviated terms
- 5 General
- 6 Testing and inspection [Go to Page]
- 6.1 Grouping [Go to Page]
- 6.1.1 General
- 6.1.2 Size groups
- Table 1 — Size groups [Go to Page]
- 6.1.3 Fitting groups
- Table 2 — Fitting groups [Go to Page]
- 6.1.4 Fitting types
- 6.2 Type testing
- Table 3 — Characteristics of compounds that require type testing (TT) by the compound manufacturer
- Table 4 — Characteristics of pipes, including coextruded pipes and peelable layer pipes that require type testing (TT)
- Table 5 — Characteristics of fittings that require type testing (TT)
- Table 6 — Characteristics of valves that require type testing (TT) [Go to Page]
- 6.3 Batch release tests
- Table 7 — Characteristics of compounds and minimum sampling frequencies for BRTs by the compound manufacturer
- Table 8 — Characteristics of pipes, including coextruded pipes and peelable layer pipes, and minimum sampling frequencies for BRTs by the pipe manufacturer
- Table 9 — Characteristics of fittings and minimum sampling frequencies for BRTs by the fitting manufacturer
- Table 10 — Characteristics of valves and minimum sampling frequencies for BRTs by the valve manufacturer [Go to Page]
- 6.4 Process verification tests
- Table 11 — Characteristics and minimum sampling frequencies for PVTs by the compound manufacturer
- Table 12 — Characteristics of pipes including coextruded and peelable layer pipes, and minimum sampling frequencies for PVTs by the pipe manufacturer
- Table 13 — Characteristics of fittings and minimum sampling frequencies for PVTs by the fitting manufacturer
- Table 14 — Characteristics and minimum sampling frequencies for PVTs by the valve manufacturer [Go to Page]
- 6.5 Audit tests
- Table 15 — Characteristics and minimum sampling frequencies for ATs for the compound
- Table 16 — Characteristics and minimum sampling frequencies for ATs for pipes, including coextruded pipes and peelable layer pipes
- Table 17 — Characteristics and minimum sampling frequencies for ATs for fittings
- Table 18 — Characteristics and minimum sampling frequencies for ATs for valves [Go to Page]
- 6.6 Indirect tests
- 6.7 One-off products and products produced in very low quantity
- 6.8 Mechanical fittings
- 6.9 Documentation [Go to Page]
- 6.9.1 Type test results
- 6.9.2 Test records
- 6.9.3 Technical file for certification purposes
- Annex A (normative) Change of compound
- A.1 General
- A.2 Change
- A.2.1 Change of base polymer
- A.2.2 Change of grade
- A.2.3 Change of pigment
- A.2.4 Change of additives other than pigments
- A.3 Type testing required for re-evaluation
- A.3.1 Changes A.2.1 and A.2.3.1
- A.3.2 Changes A.2.2.1, A.2.2.2, A.2.2.3, A.2.3.2, A.2.4.1, A.2.4.2 and A.2.4.3
- Table A.1 — Type testing required for re-evaluation
- Annex B (normative) Testing and inspection of fabricated fittings
- B.1 Grouping
- B.2 Type tests
- Table B.1 — Characteristics of swept bends that require type testing (TT)
- Table B.2 — Characteristics of segmented fittings that require type testing (TT)
- B.3 Batch release tests
- Table B.3 — Characteristics and minimum sampling frequencies for BRTs by the fabricated fitting manufacturer
- B.4 Process verification tests
- Table B.4 — Characteristics and minimum sampling frequencies for PVTs by the fabricated fitting manufacturer
- B.5 Audit tests
- Table B.5 — Characteristics and minimum sampling frequencies for ATs for fabricated fittings
- Annex C (informative) Basic test matrix for PE water compounds and piping products
- Table C.1 — Basic test matrix for PE water compounds and piping products
- Bibliography [Go to Page]
