|
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-D4354 2012ASTM D4354 - 12Standard Practice for Sampling of Geosynthetics and Rolled Erosion Control Products(RECPs) for TestingActive Standard ASTM D4354 | Developed by Subcommittee: D35.01 Book of Standards Volume: 04.13 ASTM D4354Significance and Use 5.1 This practice provides a means by which samples of geosynthetics may be selected to provide a statistically valid sample for the selection of test specimens without previous knowledge of the variability that may exist between production units. 5.2 The principles stated in Practice D4271 , and the illustrative text in that practice can be used by test method authors in preparing sampling statements. 5.3 This practice gives three procedures for sampling: one for manufacturer's quality control (MQC), one for manufacturer's quality assurance (MQA) testing, and a third for purchaser's specification conformance testing. For this reason, test methods containing a section on sampling that requires the use of this practice should contain a statement in the section on reporting similar to the following: Report which procedure from Practice D4354 was used for sampling: Procedure A for Manufacturer's Quality Control (MQC), Procedure B for Manufacturer's Quality Assurance (MQA) Testing, or Procedure C for Purchaser's Specification Conformance Testing. 5.4 Manufacturer's Quality Assurance is done internally to ensure the manufacturer of the MQC program. When it is required to provide certification to a purchaser as to quality assurance, the MQA testing is to be done by an external MQA testing facility. 1. Scope 1.1 This practice covers three procedures for the sampling of geosynthetics and rolled erosion control products (RECPs) for testing. This practice requires that instructions on taking laboratory samples and test specimens be part of every test method for geosynthetics. 1.1.1 The first procedure describes the sampling of production units for the purpose of manufacturer's quality control (MQC) ( Table 1 ).
TABLE 1 Number of Units to be Selected as Lot SampleManufacturers Quality Control
1.1.2 The second procedure describes the sampling of production units for the purpose of manufacturer's quality assurance (MQA) testing during the manufacturing process. This requires that backup statistical process control records be maintained during the manufacturing process ( Table 2 ).
TABLE 2 Number of Units to be Selected as Lot SampleManufacturer's Quality Assurance
1.1.3 The third procedure describes the division of shipments of geosynthetics and rolled erosion control products into lots and the determination of lot sample size for purchaser's specification conformance testing ( Table 3 ).
TABLE 3 Number of Units to be Selected as Lot SamplePurchaser's Specification Conformance
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM Standards D123 Terminology Relating to Textiles D4271 Practice for Writing Statements on Sampling in Test Methods for Textiles D4439 Terminology for Geosynthetics Keywords geosynthetic; quality assurance; quality control; sampling; specification conformance; testing ; ICS Code ICS Number Code 59.080.70 (Geotextiles) DOI: 10.1520/D4354-12 ASTM International is a member of CrossRef. ASTM D4354The following editions for this book are also available...This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|