1. Scope

1.1 This guide covers the minimum installation recommendations for fully adhered, hot-applied reinforced waterproofing systems on vertical and low-slope (plaza deck) surfaces.

1.2 For the purpose of this guide, the substrate is assumed to be concrete or masonry, structurally sound, able to accept the weight of anticipated loads, and meets the local building code requirements. Similarly, all components of the waterproofing system are assumed to comply with any federal, state, and local environmental regulations that may be in effect at the time of installation. Expansion joints, insulation, drainage layers, and overburden are beyond the scope of this guide.

1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

C981 Guide for Design of Built-Up Bituminous Membrane Waterproofing Systems for Building Decks

D41 Specification for Asphalt Primer Used in Roofing, Dampproofing, and Waterproofing

D43 Specification for Coal Tar Primer Used in Roofing, Dampproofing, and Waterproofing

D173 Specification for Bitumen-Saturated Cotton Fabrics Used in Roofing and Waterproofing

D226 Specification for Asphalt-Saturated Organic Felt Used in Roofing and Waterproofing

D227 Specification for Coal-Tar-Saturated Organic Felt Used in Roofing and Waterproofing

D449 Specification for Asphalt Used in Dampproofing and Waterproofing

D450 Specification for Coal-Tar Pitch Used in Roofing, Dampproofing, and Waterproofing

D1079 Terminology Relating to Roofing and Waterproofing

D1327 Specification for Bitumen-Saturated Woven Burlap Fabrics Used in Roofing and Waterproofing

D1668 Specification for Glass Fabrics (Woven and Treated) for Roofing and Waterproofing

D2178 Specification for Asphalt Glass Felt Used in Roofing and Waterproofing

D2822 Specification for Asphalt Roof Cement, Asbestos-Containing

D4022 Specification for Coal Tar Roof Cement, Asbestos Containing

D4586 Specification for Asphalt Roof Cement, Asbestos-Free

D4990 Specification for Coal Tar Glass Felt Used in Roofing and Waterproofing

D5295 Guide for Preparation of Concrete Surfaces for Adhered (Bonded) Membrane Waterproofing Systems

D5643 Specification for Coal Tar Roof Cement, Asbestos Free

D5726 Specification for Thermoplastic Fabrics Used in Hot-Applied Roofing and Waterproofing

D5898 Guide for Details for Adhered Sheet Waterproofing

D5957 Guide for Flood Testing Horizontal Waterproofing Installations

D6152 Specification for SEBS-Modified Mopping Asphalt Used in Roofing

D6162 Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcements

D6163 Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using Glass Fiber Reinforcements

D6164 Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using Polyester Reinforcements

D6451 Guide for Application of Asphalt Based Protection Board

D6506 Specification for Asphalt Based Protection Board for Below-Grade Waterproofing

Other Documents

Keywords

application; asphalt; coal tar pitch; modified bitumen; polymer-modified bitumen sheet; rubberized asphalt waterproofing; waterproofing; Application--roofing/waterproofing material; Fully-adhered waterproofing systems; Reinforced roofing/waterproofing materials; Waterproofing materials/applications;

ICS Code

ICS Number Code 91.100.50 (Binders. Sealing materials)

DOI: 10.1520/D6622-01

ASTM International is a member of CrossRef.