Significance and Use

The test method is useful for the following:

Classification of Powders The cohesion and angle of internal friction are flowability indicators of powders and can be used to classify the powders.

Quality Control For a number of industrial applications flowability factors are used to compare the material flowability at different times during production. The material produced has to be held within given limits for each application and each powder so as to ensure trouble-free operation.

Material Engineering Powder properties are influenced by particle size, particle size distribution, fat content, humidity and other parameters. By selecting the correct parameters and the correct mixtures of powders, the required mechanical properties of the product are achieved.

Design of Handling Equipment For certain storage and conveyor equipment mathematical models exist which require the mechanical properties of powders.

Note 2The quality of the result produced by this standard is dependent on the competence of personnel performing it, and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice D 3740 are generally considered capable of competent and objective testing/sampling/inspection/etc. Users of this standard are cautioned that compliance with Practice D 3740 does not in itself assure reliable results. Reliable results depend on many factors; Practice D 3740 provides a means of evaluating some of those factors. Practice D 3740 was developed for agencies engaged in the testing or inspection (or both) of soil and rock. As such it is not totally applicable to agencies performing this standard. However, users of this standard should recognize that the framework of Practice D 3740 is appropriate for evaluating the quality of an agency performing this standard. Currently there is no known qualifying national authority that inspects agencies that perform this standard.

1. Scope

1.1 This test method is applied to the measurement of the mechanical properties of powders as a function of normal stress.

1.2 This apparatus is suitable measuring the properties of powders and other bulk solids, up to a particle size of 5000 micron.

1.3 This method comprises four different test procedures for the determination of powder mechanical properties:

1.3.1 Test A Measurement of INTERNAL FRICTION as a function of normal stress.

1.3.2 Test B Measurement of WALL FRICTION as a function of normal stress.

1.3.3 Test C Measurement of BULK DENSITY as a function of normal stress and time.

1.3.4 Test D Measurement of DEGRADATION as a function of normal stress.

1.4 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D 6026 .

1.4.1 The procedures used to specify how data are collected/recorded or calculated in this standard are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user s objectives, and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of this standard to consider significant digits used in analysis methods for engineering design.

1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

D653 Terminology Relating to Soil, Rock, and Contained Fluids

D3740 Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction

D6026 Practice for Using Significant Digits in Geotechnical Data

Keywords

bulk density; bulk solids; cohesive strength; degradation; flowability; internal friction; Peschl shear tester; rotational shear tester; shear stress; wall friction; Bulk density; Cohesive strength; Degradation--environmental materials/applications; Internal friction testing; Peschl shear tester; Powders; Shear stress; Shear testing--soil; Wall friction ;

ICS Code

ICS Number Code 77.160 (Powder metallurgy)

DOI: 10.1520/D6682-08

ASTM International is a member of CrossRef.

ASTM D6682