Significance and Use

International standard ANS/ISO/IEC 17025 promotes the use of documented accountability and quality control procedures to assure a laboratory and its clients that the laboratory can produce technically valid data and results in the routine performance of its sampling, sample preparation and testing activities.

A laboratory shall use ANSI/ISO/IEC 17025 to develop its quality system. Clause 4 of ANS/ISO/IEC 17025 specifies the requirements for sound management. Clause 5 of ANS/ISO/IEC 17025 specifies the requirements for technical competence for the type of tests or calibrations, or both the laboratory undertakes.

In addition to complying with the requirements of ANS/ISO/IEC 17025, the Annex of this standard practice contains information that shall be considered important for the evaluation and operation of a competent Coal and Coke sampling or testing facility, or both. The information in this Annex is presented where it is not otherwise covered in ANS/ISO/IEC 17025 or the applicable ASTM methods.

Laboratory clients, regulatory authorities, and accreditation bodies that recognize the competence of testing and calibration laboratories can use this standard practice as the basis for their evaluation.

The primary significance of this practice is to establish that for a laboratory to generate measurements traceable to SI units, it must:

Have a clear understanding of the work requested by the client.

Meet the quality system requirements of the internationally accepted ANS/ISO/IEC 17025 standard.

Use test methods which have been shown to be traceable to SI units of measurement

Be able to demonstrate that the laboratory is in statistical control at the time the measurements are made.

1. Scope

1.1 This practice specifies requirements to operate and evaluate the quality and management systems in a laboratory that provides services with respect to sample collection, sample preparation, or testing of coal, coke, and ash derived from coal or coke using ASTM standards that are under the jurisdiction of Committee D05 on Coal and Coke.

Note 1The word laboratory is used throughout this practice when referring to an organization that provides services in coal sampling or testing, or both. It is recognized, however, that the word may not be appropriate to an organization that does not perform actual laboratory sample testing.

1.2 International standard ANS/ISO/IEC 17025 shall be the governing document specifying requirements for management, technical competence and evaluation of a laboratory.

Note 2An accrediting body or user of laboratory services can also impose technical or non-technical requirements not specifically addressed in ANS/ISO/IEC 17025 provided they do not invalidate the requirements of ANS/ISO/IEC 17025.

1.3 This practice is used to evaluate only those capabilites specifically claimed by a laboratory.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

D121 Terminology of Coal and Coke

D3174 Test Method for Ash in the Analysis Sample of Coal and Coke from Coal

D4239 Test Method for Sulfur in the Analysis Sample of Coal and Coke Using High-Temperature Tube Furnace Combustion

D4749 Test Method for Performing the Sieve Analysis of Coal and Designating Coal Size

D5061 Test Method for Microscopical Determination of the Textural Components of Metallurgical Coke

D5515 Test Method for Determination of the Swelling Properties of Bituminous Coal Using a Dilatometer

D6172 Test Method for Determining the Volume of Bulk Materials Using Contours or Cross Sections Created by Direct Operator Compilation Using Photogrammetric Procedures

D6349 Test Method for Determination of Major and Minor Elements in Coal, Coke, and Solid Residues from Combustion of Coal and Coke by Inductively Coupled Plasma--Atomic Emission Spectrometry

E177 Practice for Use of the Terms Precision and Bias in ASTM Test Methods

E456 Terminology Relating to Quality and Statistics

E2554 Practice for Estimating and Monitoring the Uncertainty of Test Results of a Test Method in a Single Laboratory Using a Control Sample Program

ANS/ISO/IEC Document

Keywords

accuracy; competence; evaluation; laboratory; management; stability;

ICS Code

ICS Number Code 75.160.10 (Solid fuels)

DOI: 10.1520/D7448-09

ASTM International is a member of CrossRef.

ASTM D7448