|
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-E3536/E3536M 2026ASTM E3536/E3536M-26Active Standard: Standard Specification for Compacted Mineral-Insulated, Niobium-Sheathed, High Temperature Irradiation Resistant ThermocouplesASTM E3536/E3536MScope 1.1 This specification covers dimensional and material requirements for compacted, mineral-insulated, niobium-sheathed, high temperature, irradiation resistant thermocouples (HTIR-TC) with one HTIR-TC thermoelement pair. These types of thermocouples are suitable for high neutron fluence, up to 1022 n/cm2, and a high temperature, up to 1600 °C [2912 °F]. 1.1.1 This specification exceeds the temperature limitations of Specification E235/E235M for Type K and N. When nuclear applications are above 1260 °C [2300 °F] this standard should be considered. 1.1.2 This specification defines the diameter of the HTIR-TC MIMS cable as ranging from 0.059 in. [1.5 mm] to 0.062 in. [1.6 mm] to accommodate the nuclear fuel pin size and compactness. This has been found to be the optimal diameter for this application without compromising reliability of the sensor but to fit appropriately inside the fuel pin. 1.1.3 This specification was prepared to detail requirements for HTIR-TCs for use in nuclear environments, but they can also be used for laboratory or general commercial applications where the environmental conditions exceed normal service requirements. The intended use of the HTIR-TC in a specific nuclear application will require an evaluation of the compatibility of the thermocouple, including the effect of the temperature, atmosphere, and integrated neutron flux on the materials and accuracy of the thermoelements in the proposed application by the purchaser. 1.2 This specification describes processing, testing, and quality assurance requirements for HTIR-TCs as well as optional supplementary tests. 1.3 Provisions are made for selecting the type of thermocouple or thermoelements, alumina (Al2O3) insulation or other appropriate insulator material, and niobium (Nb) sheath material. Provisions are also made for selecting a transition or termination. 1.4 The values stated in inch-pound units or SI (metric) units may be regarded separately as standard. The values stated in each system are not the exact equivalents, and each system shall be used independently of the other. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords junction; metal-sheathed; moisture seal; sheathed thermocouples; termination; thermocouple; thermoelement; HTIR-TC; ICS Code ICS Number Code n/a DOI: 10.1520/E3536_E3536M-26 This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|