|
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-F3728 2024ASTM F3728-24Active Standard: Standard Specification for Release Characteristics of Ski-Binding-Boot (S-B-B) Systems for Recreational SkiingASTM F3728Scope 1.1 This specification covers the required release and retention characteristics of ski-binding-boot (S-B-B) systems. This specification is applicable to all recreational snow skiing bindings that have safety release mechanisms. Specifically, this performance standard establishes the minimum performance requirement for release and retention of a ski boot in a ski binding under loading scenarios that relate to ski shop testing and loads that simulate forward and backward twisting falls. 1.2 This specification is a performance standard and is not intended to restrict design. Although a S-B-B system that meets this specification will help reduce the risk of some types of injuries to the tibia and fibula in some falls and accidents, the protection is limited, and skiing involves inherent risks of injury; this standard does not purport to address all the safety concerns, if any, associated with its use, and it is to be clearly understood that compliance with this standard and other applicable standards or guidelines in no way guarantees that injury can be prevented. The user is responsible for participating in the sport within his/her abilities and the nature of the snow conditions which may vary widely. Compliance with the common-sense rules of the sport’s safety, including any applicable responsibility codes, is essential to help reduce the risk of personal injury. 1.3 All testing and requirements of this specification shall be in accordance with Test Method F504-05(2022), except where noted herein. 1.4 This specification is intended for use with all recreational S-B-B systems, including systems labeled as alpine, alpine touring (including pin/tech systems), systems that use alpine boots with improved walking soles (walking or GripWalk), and systems that use pins as part of the ski binding-boot interface. Use of ski bindings that do not meet the requirements of this standard or using incompatible combinations of ski bindings and boots can cause unexpected release and retention characteristics. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords compatibility testing; ski bindings; ski boots; skiing; ICS Code ICS Number Code 97.220.20 (Winter sports equipment) DOI: 10.1520/F3728-24 This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|