|
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Content DescriptionThis standard describes 3-in. through 64-in. (80-mm through 1,600-mm)6 ductile-iron compact fittings to be used with ductile-iron pipe or pipe made of other materials with similar outside diameters for conveying potable water, wastewater, and reclaimed water. Minimum working pressures by size range are as follows: 3?in. through 24 in. (80 mm through 600 mm): 350 psi (2,413 kPa); 30 in. through 48 in. (750 mm through 1,200?mm): 250 psi (1,724 kPa); and 54 in. through 64 in. (1,400 mm through 1,600 mm): 150 psi (1,034?kPa). Fittings are adequate for the rated working pressure plus a surge allowance of 100 psi or a surge allowance of half the rated working pressure, whichever is less. Fittings with mechanical joints are listed in this standard for the 3-in. through 64-in. (80-mm through 1,600-mm) sizes. The standard also may be used for fittings of these sizes with push-on joints or other joints as agreed on at the time of purchase. Fittings with push-on joints and flanged joints are listed in this standard for the 54-in. through 64-in. (1,400-mm through 1,600-mm) sizes. Fittings with flange joints are not discussed in this standard for sizes 3?in. through 48 in. (80 mm through 1,200 mm) because of the importance of standardized center-to-flange face dimensions for these sizes already described in ANSI7/AWWA C110/A21.10. Fittings with plain ends are listed for bends and reducers of the 3-in. through 64-in. (80-mm through 1,600-mm) size range and for tees and crosses of the 54-in. through 64-in. (1,400-mm through 1,600-mm) size range. This standard can be referenced in specifications for ductile-iron compact fittings, 3?in. through 64 in. (80?mm through 1,600 mm). The stipulations of this standard apply when this document has been referenced and then only to ductile-iron compact fittings, 3 in. through 64?in. (80 mm through 1,600 mm).Subscription InformationMADCAD.com AWWA Standards & Manuals subscriptions are annual and access is concurrency based (number of people that can access the subscription at any given time).
Some features of MADCAD.com AWWA Standards & Manuals Subscriptions are:
- Floating concurrency model: Set your concurrency level and share your AWWA Standards & Manuals Subscriptions among your offices enterprise-wide.
- Immediate Access: As soon as the transaction is completed, your AWWA Standards & Manuals Subscription will be ready for access.
For any further information on MADCAD.com AWWA Standards & Manuals Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About AWWAEstablished in 1881, the American Water Works Association is the oldest and largest nonprofit, scientific and educational organization dedicated to safe and sustainable water in the world. With more than 50,000 members worldwide and 43 Sections in North America, AWWA advances public health, safety and welfare by uniting the efforts of the entire water community. AWWA Offers education to water professionals Advocates for safe and sustainable water Collects and share knowledge Creates volunteering opportunities |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|