Cart (0)
  • No items in cart.
Total
$0
There is a technical issue about last added item. You can click "Report to us" button to let us know and we resolve the issue and return back to you or you can continue without last item via click to continue button.
Home
Content
eLibrary
Filters:
EDITION
to
PUBLISHER
AABC
(1)
AAMI
(353)
ACI
(651)
AECDAILY
(599)
AISC
(58)
ASA
(290)
ASCE
(1042)
ASHRAE
(728)
ASME
(2262)
ASSE
(117)
ASTM
(97896)
AWC
(58)
AWWA
(635)
BHMA
(132)
BICSI
(33)
BIFMA
(28)
BOMA
(20)
BSI
(99791)
CRSI
(18)
IAHSS
(1)
IAPMO
(396)
ICC
(328)
IEC
(10763)
IEEE
(7368)
IES
(252)
ISEA
(21)
ISO
(24378)
Joint Commission
(198)
Joint Commission Int.
(1)
NEMA
(910)
NETA
(7)
NFPA
(1722)
TCNA
(23)
TMS
(19)
USGBC
(28)
WILEY
(4)
 
AR
(6)
AZ
(7)
CA
(128)
CO
(1)
CT
(3)
FL
(58)
ID
(5)
IL
(5)
IN
(1)
KY
(1)
LA
(2)
MI
(28)
MN
(27)
NC
(36)
NJ
(13)
NY
(71)
OH
(24)
OR
(25)
PA
(7)
RI
(8)
SC
(20)
SD
(1)
TX
(3)
VA
(50)
VT
(6)
WA
(34)
CONTENT TYPE
 Act
 Admin Code
 Announcements
 Bill
 Book
 CADD File
 CAN
 CEU
 Charter
 Checklist
 City Code
 Code
 Commentary
 Comprehensive Plan
 Conference Paper
 County Code
 Course
 DHS Documents
 Document
 Errata
 Executive Regulation
 Federal Guideline
 Firm Content
 Guideline
 Handbook
 Interpretation
 Journal
 Land Use and Development
 Law
 Legislative Rule
 Local Amendment
 Local Code
 Local Document
 Local Regulation
 Local Standards
 Manual
 Model Code
 Model Standard
 Notice
 Ordinance
 Other
 Paperback
 PASS
 Periodicals
 PIN
 Plan
 Policy
 Product
 Product - Data Sheet
 Program
 Provisions
 Requirements
 Revisions
 Rules & Regulations
 Standards
 State Amendment
 State Code
 State Manual
 State Plan
 State Standards
 Statute
 Study Guide
 Supplement
 Sustainability
 Technical Bulletin
 All
  • ISO
    ISO 8513:2023 Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Test methods for the determination of the initial longitudinal tensile strength
    Edition: 2023
    $192.38
    / user per year

Content Description

This document specifies two test methods (method A and method B) for determining the longitudinal tensile properties of glass-reinforced thermosetting plastics (GRP) pipes. The properties which can be determined are:

—     the longitudinal tensile strength, and

—     the percentage ultimate elongation.

Method A uses, for the test piece(s), a longitudinal strip cut from a pipe.

Method B uses a specified length of the full cross-section of the pipe.

Method A is applicable to pipes with a nominal size of DN 50 or greater with circumferentially-wound filaments, with or without chopped glass and/or woven rovings and/or fillers, and to centrifugally-cast pipes. It is applicable to pipes with helically wound filaments with a nominal size of DN 200 or greater.

Method B is applicable to all types of GRP pipe. It is usually used for pipes with a nominal size up to and including DN 150.

Results from one method are not necessarily equal to the results derived from any of the alternative methods. However, all methods have equal validity.

Annex A describes additional considerations for method B that have been found useful for the testing of thin-walled helically-wound pipes and can be used to supplement the basic text.

NOTE            This document does not address the determination of longitudinal tensile modulus. Due to the multi-layer construction of many GRP pipes, the accurate measurement of strain, necessary for modulus determination, can be very difficult. If it is desired to determine longitudinal modulus, see ISO 527-4 and/or ISO 527-5.



About ISO

ISO, the International Organization for Standardization, brings global experts together to agree on the best way of doing things – for anything from making a product to managing a process. As one of the oldest non-governmental international organizations, ISO has enabled trade and cooperation between people and companies all over the world since 1946. The International Standards published by ISO serve to make lives easier, safer and better.
GROUPS