eLibrary >
BS EN ISO 13856-2:2013 Safety of machinery. Pressure-sensitive protective devices - General principles for design and testing of pressure-sensitive edges and pressure-sensitive bars >
BS EN ISO 13856-2:2013 Safety of machinery. Pressure-sensitive protective devices - General principles for design and testing of pressure-sensitive edges and pressure-sensitive bars, 2013
- Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC
- Table tab_1
- Section sec_1
- Section sec_2
- Section sec_3
- Table tab_a
- Figure fig_1
- Section sec_4
- Section sec_4.1
- Table tab_b
- Figure fig_2
- Table tab_c
- Figure fig_3
- Section sec_4.2
- Table tab_2
- Section sec_4.3
- Section sec_4.4
- Section sec_4.5
- Section sec_4.6
- Table tab_d
- Figure fig_4
- Figure fig_5
- Section sec_4.7
- Section sec_4.8
- Section sec_4.8.1
- Section sec_4.8.2
- Section sec_4.8.3
- Section sec_4.9
- Section sec_4.10
- Section sec_4.10.1
- Section sec_4.10.2
- Section sec_4.11
- Section sec_4.12
- Section sec_4.12.1
- Section sec_4.12.2
- Section sec_4.12.3
- Section sec_4.12.4
- Section sec_4.12.5
- Section sec_4.13
- Section sec_4.13.1
- Section sec_4.13.2
- Section sec_4.13.3
- Section sec_4.14
- Section sec_4.14.1
- Section sec_4.14.2
- Section sec_4.14.3
- Section sec_4.14.4
- Section sec_4.14.5
- Section sec_4.14.6
- Section sec_4.14.7
- Section sec_4.15
- Section sec_4.16
- Section sec_4.17
- Section sec_4.17.1
- Section sec_4.17.2
- Section sec_4.18
- Section sec_4.19
- Section sec_4.20
- Section sec_4.20.1
- Section sec_4.20.2
- Section sec_4.20.3
- Section sec_4.20.4
- Section sec_4.21
- Section sec_4.22
- Section sec_4.23
- Table tab_3
- Section sec_4.24
- Section sec_4.25
- Section sec_4.26
- Section sec_4.27
- Section sec_5
- Section sec_5.1
- Section sec_5.2
- Section sec_5.3
- Section sec_5.4
- Section sec_6
- Section sec_6.1
- Section sec_6.2
- Section sec_6.3
- Section sec_6.3.1
- Section sec_6.3.2
- Section sec_7
- Section sec_7.1
- Section sec_7.2
- Section sec_7.2.1
- Table tab_4
- Section sec_7.2.2
- Section sec_7.3
- Section sec_7.4
- Section sec_7.5
- Section sec_7.5.1
- Section sec_7.5.2
- Section sec_7.5.2.1
- Section sec_7.5.2.2
- Section sec_7.5.2.3
- Figure fig_6
- Section sec_7.5.3
- Section sec_7.6
- Section sec_7.6.1
- Section sec_7.6.2
- Section sec_7.6.3
- Section sec_7.6.4
- Section sec_7.6.5
- Table tab_g
- Figure fig_7
- Table tab_5
- Table tab_6
- Table tab_h
- Figure fig_8
- Table tab_7
- Table tab_8
- Table tab_9
- Table tab_10
- Section sec_7.7
- Section sec_7.7.1
- Section sec_7.7.2
- Section sec_7.7.3
- Section sec_7.7.4
- Section sec_7.8
- Section sec_7.8.1
- Section sec_7.8.2
- Section sec_7.8.3
- Section sec_7.9
- Section sec_7.10
- Section sec_7.11
- Section sec_7.11.1
- Section sec_7.11.2
- Table tab_11
- Section sec_7.11.3
- Table tab_12
- Section sec_7.11.4
- Table tab_13
- Section sec_7.11.5
- Table tab_14
- Section sec_7.11.6
- Table tab_15
- Section sec_7.12
- Section sec_7.12.1
- Section sec_7.12.2
- Section sec_7.12.3
- Section sec_7.13
- Section sec_7.13.1
- Section sec_7.13.2
- Section sec_7.13.3
- Section sec_7.14
- Section sec_7.15
- Section sec_7.16
- Section sec_7.17
- Section sec_7.17.1
- Section sec_7.17.2
- Section sec_7.18
- Section sec_7.19
- Section sec_7.20
- Section sec_7.21
- Section sec_7.22
- Section sec_7.23
- Section sec_7.24
- Section sec_7.25
- Section sec_7.26
- Annex sec_A
- Table tab_i
- Figure fig_A.1
- Table tab_j
- Figure fig_A.2
- Table tab_k
- Figure fig_A.3
- Table tab_l
- Figure fig_A.4
- Annex sec_B
- Table tab_m
- Figure fig_B.1
- Annex sec_C
- Annex sec_C.1
- Annex sec_C.2
- Annex sec_C.2.1
- Annex sec_C.2.2
- Annex sec_D
- Annex sec_D.1
- Annex sec_D.2
- Annex sec_D.2.1
- Annex sec_D.2.2
- Annex sec_D.2.3
- Annex sec_D.3
- Annex sec_D.3.1
- Annex sec_D.3.2
- Annex sec_D.3.3
- Annex sec_D.3.4
- Annex sec_D.3.5
- Annex sec_D.3.6
- Annex sec_D.4
- Annex sec_D.4.1
- Annex sec_D.4.2
- Annex sec_D.4.3
- Annex sec_E
- Annex sec_E.1
- Annex sec_E.2
- Annex sec_E.3
- Annex sec_F
- Annex sec_F.1
- Annex sec_F.2
- Annex sec_F.3
- Annex sec_F.4
- Annex sec_F.5
- Annex sec_G
- Annex sec_G.1
- Annex sec_G.2
- Annex sec_G.3
- Annex sec_G.3.1
- Annex sec_G.3.2
- Annex sec_G.3.3
- Reference ref_1
- Reference ref_2
- Reference ref_3
- Reference ref_4
- Reference ref_5
- Foreword
- Introduction
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 Requirements for design and testing
- 4.1 Effective sensing surface
- 4.2 Actuating force for testing
- 4.3 Pre-travel
- 4.4 Working travel
- 4.5 Overtravel
- 4.6 Force–travel relationships
- 4.7 Minimum operating speed
- 4.8 Number of operations
- 4.9 Sensor output
- 4.10 Response of output signal switching device to actuating force
- 4.11 Reset function
- 4.12 Environmental conditions
- 4.13 Power supply variations
- 4.14 Electrical equipment
- 4.15 Hydraulic equipment
- 4.16 Pneumatic equipment
- 4.17 Enclosure
- 4.18 Additional coverings for sensors
- 4.19 Access
- 4.20 Performance levels and categories for SRP/CSs in accordance with ISO 13849‑1
- 4.21 Adjustments
- 4.22 Sensor fixing and mechanical strength
- 4.23 Recovery after deformation
- 4.24 Connections
- 4.25 Sharp corners, sharp edges and rough surfaces
- 4.26 Mechanical features
- 4.27 Inhibition and blocking
- 5 Marking
- 6 Information for selection and use
- 6.1 General
- 6.2 Essential data for the selection of suitable pressure‑sensitive edge or pressure‑sensitive bar
- 6.3 Information for use
- 7 Verification of requirements
- 7.1 General
- 7.2 Test samples
- 7.3 Test pieces
- 7.4 Test No. 1 — Safety-related data for selection, installation, commissioning, operation and maintenance of suitable pressure-sensitive edges or pressure-sensitive bars
- 7.5 Test No. 2 — Mounting orientations of sensors
- 7.6 Test No. 3 — Actuating force
- 7.7 Test No. 4 — Force–travel relationship(s)
- 7.8 Test No. 5 — Number of operations
- 7.9 Test No. 6 — Output state of sensor and output signal switching device
- 7.10 Test No. 7 — Response of output signal switching device to actuating force, reset and state of power supply
- 7.11 Test No. 8 — Environmental conditions
- 7.12 Test No. 9 — Power supply variation
- 7.13 Test No. 10 — Electrical, hydraulic and pneumatic equipment
- 7.14 Test No. 11 — Enclosure
- 7.15 Test No. 12 — Additional coverings for sensors
- 7.16 Test No. 13 — Access
- 7.17 Test No. 14 — Performance Level (PL) according to ISO 13849‑1
- 7.18 Test No. 15 — Adjustments
- 7.19 Test No. 16 — Sensor fixing and mechanical strength
- 7.20 Test No. 17 — Recovery after deformation
- 7.21 Test No. 18 — Connections
- 7.22 Test No. 19 — Sharp corners, sharp edges and rough surfaces
- 7.23 Test No. 20 — Mechanical features
- 7.24 Test No. 21 — Inhibition and blocking
- 7.25 Test No. 22 — Marking
- 7.26 Test No. 23 — Information for selection and use
- Annex A (normative) Timing diagrams for pressure-sensitive edges/bars with/without reset
- Annex B (informative) Operating speed, force and travel — Explanatory remarks and recommendations
- Annex C (informative) Device selection guidance for machinery manufacturer/user
- Annex D (informative) Design guidance
- Annex E (informative) Application guidance
- Annex F (informative) Guidance on commissioning and testing after installation
- Annex G (informative) General considerations for systems meeting ISO 13849‑1, category 2
- Bibliography [Go to Page]